SPECT and SPECT-CT Imaging Protocols



SPECT and SPECT-CT Imaging Protocols


Daniela B. Husarik

Thomas F. Hany





Introduction

Conventional nuclear medicine imaging has proven to be a functional imaging modality, but most nuclear images contain little anatomic information. CT, on the other hand, has demonstrated that it provides excellent anatomic information, but it contains little to no functional information. Image coregistration with various morphologic imaging modalities (CT or MRI) with dedicated software has substantial merit, as it results in significantly improved image interpretation, reducing the amount of uncertainty regarding the location of a lesion observed in a nuclear scan. The disadvantage of using software coregistration is that exactly coregistered patient positioning in both imaging modalities is difficult to guarantee. Extrinsic markers and mattresses providing “cast-like” forms increase the exactness of patient positioning during imaging with the two modalities intended for coregistration but are cumbersome logistically. In bone scans, this is not necessary, as there are sufficient anatomical landmarks on SPECT for later image fusion with coregistration software. Postprocessing to integrate the two data sets from different imaging devices can be time consuming. The breakthrough is achieved with integration of anatomic and functional imaging in one imaging device, a SPECT-CT gamma camera or a PET-CT camera (1,2).

SPECT-CT cameras have the advantage that all conventional nuclear medicine imaging can be performed with them, and when required, integrated anatomic and functional imaging can be done without the need for patient repositioning or rescanning elsewhere. No postprocessing is needed for image coregistration with such a system. Additionally or alternatively, when required, the CT data can be used for attenuation correction to improve SPECT image quality (3,4,5).






Figure 20.1 Indium 111 [111In]octreotide scan in a 75-year-old male patient with known liver metastases of a intestinal carcinoid tumor. Whole-body anteroposterior and posteroanterior planar images 5 hours after injection (A) reveal multiple metastases in the liver and an unclear uptake in the dorsal aspect of the thorax. In the maximal intensity projection image (B) of the SPECT acquisition of the chest, uptake is seen in the midthorax. SPECT-CT images clearly locate the radiotracer uptake in a vertebral body in the thoracic spine, representing an osseous metastasis. C: SPECT image. D: CT image. E: SPECT-CT image.


There is one key difference between SPECT-CT and PET-CT. The cost of the integrated device parts is heavily weighted toward CT if a high-end CT is used in a SPECT-CT system, and SPECT data acquisition is substantially slower than PET data acquisition. As a result, it may be much less attractive financially to own a SPECT-CT system with a high-end CT, as the expensive CT idles much of the time when the combined system is used for an examination, and billable examination costs for SPECT-CT are typically lower than for PET-CT.


SPECT-CT Hardware

Several systems are commercially available that integrate dual-head gamma cameras with different CT systems (e.g., the Siemens Symbia T, T2, and T6; the Philips Precedence 6 and 16 slice; and the GE Healthcare Infinia and Hawkeye). These systems have all-energy digital detectors with 5/8- or 1-inch special crystals, with an energy range from thallium to fluorodeoxyglucose (FDG). The axial scan length is 40 cm, with an effective field of view of 540 × 400 mm. In certain low-dose CT systems (like the Hawkeye system), the x-ray tube is mounted on the same slip-ring gantry as the two gamma camera heads. In these systems, the tube voltage is 140 kV, and a fixed current of 2.5 mA is used. The acquisition time for one slice is approximately 15 to 20 seconds, using data from a half scan to reconstruct one slice with a standard thickness of 10 mm and a maximum in-plane resolution of 256 × 256. CT data can be used for attenuation correction and anatomic information. No additional postprocessing is necessary for image coregistration. A typical acquisition time for a SPECT-CT on the Hawkeye with a 40-cm axial field of view is 40 to 60 minutes, depending on the type of radiopharmaceutical used and the field of view covered. In other systems, the CT system operates independently and is mounted in line with the center of the SPECT gantry, very much as in PET-CT systems. The CT systems used are medium to high-end and have up to 16-slice CT scanners. The major advantage of such systems is that, like PET-CT systems, they are able to acquire fully diagnostic, intravenous contrast–enhanced CT images in the region of interest.


As mentioned, SPECT in bone scans with technetium 99m [99mTc]phosphonates can be followed by a CT scan on a stand-alone machine. For bone scans, attenuation correction is not necessary, and images can be fused after completion of the examination with coregistration software.


Quality Assurance and Control

Quality control consists of daily, weekly, and trimonthly tests. On a daily basis, we always reset the gantry parameters and test the pressure-sensitive detector control for patient safety. Daily quality control for the CT simply involves performing a blank scan. A pulse height analysis acquisition, energy peak position, and energy resolution for the gamma camera are obtained by acquiring data from an extrinsic flood source and applying energy, linearity, and sensitivity corrections. The flood uniformity is calculated by using National Electrical Manufacturers Association (NEMA) standards. A sealed cobalt 57 (57Co) source is preferred to a 99mTc flood source because it is easier to handle and avoids possible contamination. This quality control test confirms the stability of the system performance characteristics.

Weekly quality control involves removing the collimators and performing an intrinsic flood source acquisition with a technetium point source with the recommended dose, distance, and height given by the manufacturer for a specific number of total counts per detector head at a given count rate per second. This weekly intrinsic quality control test calculates the pulse height analysis acquisition, energy peak position, and energy resolution for the gamma camera. A trimonthly center-of-rotation quality control test should also be performed.


Patient Scheduling

Optimization of patient throughput in a conventional nuclear medicine unit is highly dependent on the radiotracers used, the imaging protocols, proper patient preparation, and punctual arrival of patients for their examinations. The critical factor for throughput is the decision when to use SPECT-CT clinically. In systems where the CT is relatively slow, the prudent use of CT for attenuation correction for quantification or image fusion for localization of abnormal uptake will determine how many studies can be performed on the camera during the hours of operation.

Only gold members can continue reading. Log In or Register to continue

Stay updated, free articles. Join our Telegram channel

Jul 27, 2016 | Posted by in GENERAL RADIOLOGY | Comments Off on SPECT and SPECT-CT Imaging Protocols

Full access? Get Clinical Tree

Get Clinical Tree app for offline access